Showing results: 31 - 45 of 405 items found.
-
TCR-600 -
NAPSON Corp.
*Controlled Thermo-chuck (room temperature~600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy:±(0.5% + 1℃)
-
WS-3000 -
NAPSON Corp.
*Automatic probe head selection(exchanger) among 4 kinds of probe head*[No need to exchange a probe head by each different sample measurement]*Edge 1mm measurement is available by dual meas. mode*High cost performance from high speed measurement*FOUP compatible, GEM / SECS compatible
-
RT-3000/RG-1000F -
NAPSON Corp.
*Fully automatic system for large sizes of flat panel with glass loading robot*Tester self-test function, Measurement position correction function, wide measurement range*Min. 0.1 mm meas. resolution and user programmable test pattern*Host (CIM) communication and 2-D/3-D Mapping software
-
M9033A -
Keysight Technologies
The M9033A PXIe System Synchronization Module is a dual-slot, 5-port module that provides multi-module and multi-chassis synchronization and triggering for Keysight's modular instruments.
-
M9032A -
Keysight Technologies
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
VS-SECM (DC And AC) -
Ametek Scientific Instruments
The SECM integrates a positioning system, a bipotentiostat, and an ultramicroelectrode probe or tip. The positioning system moves the probe close to the surface of the sample, within the local imaging zone. The bipotentiostat can polarize the probe only (feedback mode) or the sample and the probe independently (generator-collector mode), while measuring the resulting current(s). The probe is specially designed to have a specific tapered polish (per the RG ratio) and active radius below 100 microns. The positioning system scans the probe and charts position with measured electrochemical parameters, creating a data map of local current.
-
CSE Co.,Ltd
Vertical Probe Card. (Mobile D-RAM, L.D.I Flip Chip 60um Pitch,. System LSI, Soc Devices). Cantilever Probe Card. Low Leakage Probe Card.
-
Langer EMV-Technik GmbH
The measurement coil is located vertically in the probe head. The near field probes are run with a positioning system (Langer Scanner).
-
PrecisionWoRx -
Onto Innovation
The PrecisionWoRx VX4 System gives test facilities and probe card manufacturers the ability to confidently test tighter pitches and smaller probe tips. The system can be easily configured to specific requirements for a variety of probe card technologies. For processes using cards with very small probe tips, the system’s high-resolution optics deliver a detailed field-of-view for high accuracy and repeatability.
-
Langer EMV-Technik GmbH
The measuring coil is horizontally located in the probe head. The near field micro probes are operated with a positioning system (Langer Scanner).
-
RTU Series -
VeEX Inc.
VeEX’s Remote Test Units (RTU) are self-contained, scalable test and monitoring probes for communications networks. When used as part of the VeSion cloud-based monitoring system, these rackmount probes are optimized to work with a centralized server system. In addition, the probes can be operated in standalone mode via web browser.
-
SPS-1000, SPS-2000, and SPS-2200 -
MicroXact, Inc.
The SPS-1000, SPS-2000, and SPS-2200 systems are MicroXact’s premier manual probe stations designed to be flexible and easy to use. The high level of performance and affordability of these manual probe systems put them in a class of their own.
-
DiagnoSYS Systems Ltd
The AutoPoint DT system is a benchtop flying probe system, sometimes called a roving probe, used for automatic probing of an electronic PCB or CCA. Tasks that were previously accomplished with time-consuming manual methods can now be automated.
-
SmartScan BASIC -
Amber Precision Instruments
The BASIC is manually operated system for performing susceptibility scanning at the system level with minimal data storage capability. This system includes:1. Up to 8kV (optional. 4kV base) pulse generator for ESD susceptibility testing- Camera and camera shutter to take DUT picture and failing spots- Control computer2. Up to 8kV Probe Sets:- 1mm Hx/y Field Probe- 5mm Hx/y Field Probe- D=8mm Hz Field Probe- D=8mm Ez Field Probe- Contact API for custom design probes3. Manual input of testing location and failing condition over the DUT to be included in final report.
-
Automation Products, Inc.
Sample handling and probe mounting may often be the deciding factors in a successful viscosity measuring system. The EZL Viscosity Mounting System provides an excellent mounting platform for in-line viscosity measurement with the Dynatrol® DV Viscosity Probes.